|2012-02||Intel 64 bit||Lion - 10.7.3, Xcode 4.1||MacPorts||darcs HEAD 2012-02-20||7.4.1 (built from source, 64 bit)|
|2011-08||Intel 32 bit||Snow Leopard||2.24.5 HomeBrew||gtk-0.12.0||7.0.3||2011.2.0.1|
|2011-03||Intel 64 bit||Leopard||MacPorts||6.10|
HomeBrew (last checked 2011-08)
brew update brew install gtk+ libglade gtk-demo
If the gtk-demo appears to work, proceed to the rest of the ThreadScope install.
Problem: Bus error
Try running the gtk-demo program. Does it also fail?If so, did you try updating your port? For example, if you are using Howebrew try:
brew update brew install gtk+Then try gtk-demo again and finally
cabal install --renistall gtk
It may be worthwhile to try a gtkhs helloworld
MacPorts (last checked 2011-03-10)
- Install MacPorts (macports.org)
- Add +universal to /opt/local/etc/macports/variants.conf (not needed on 32bit)
sudo port install ghc gtk2 gvfs cairo librsvg libglade2 gtkglext gtksourceview2 && sudo port install gtk2hs -universal
This explains how to install Gtk2Hs-0.10.1 on Mac OS X 10.6 Snow Leopard, in combination with GTK+ from MacPorts.
- Install the Haskell Platform for Mac
- Download gtk2hs from gtk2hs website and untar it.
- Install gtk, cairo, etc. from MacPorts like this (note that the +universal is needed; if you already installed gtk or one of its dependencies, it is recommended you reinstall those as detailed in the NB at the end of this section).
sudo port install gtk +universal
- go to the directory where gtk2hs is untarred and run
./configure --disable-split-objs --disable-gio make sudo make install
Alternatively, if you wish to follow the Mac OS X style of directory layout, you can use this configure command instead:
./configure --with-pkgconf=/Users/username/.ghc/i386-darwin-6.10.4/package.conf --prefix=/Users/username/Library/Haskell/packages/gtk2hs --disable-split-objs --disable-gio
Where username is your username ofcourse. Right now you should be able to run the demos. Unfortunately, to build any libraries depending on gtk2hs, such as Chart, you need to edit one more file. You will need to find "package.conf" for your ghc by doing
In the output you will see the full directory to your package.conf file. In this file, you need to search for "gthread", and everywhere you can find it, add "/opt/local/lib" (with quotes) to the libraryDirs array before it.
If all went well, it should be properly installed now.
NB: If compiling fails with architecture errors for certain dynlibs, you need to reinstall the packages these dynlibs belong to with +universal by doing
sudo port upgrade packagename --enforce-variants +universal
Alternatively, and this is recommended, you can follow the steps on Haskell On Snow Leopard Blogpost to immediately add the universal variant of each package:
- Edit /opt/local/macports/variants.conf and add +universal to the end of this file
- sudo port selfupdate
- sudo port sync
- sudo port upgrade --force installed
GTK+ OS X Framework
This explains how to install Gtk2Hs on Macs using the native GTK+ OS X Framework, a port of GTK+ to the Mac that does not depend on X11, and hence, is better integrated into the Mac desktop - i.e., menus actually appear in the menu bar, where they belong. It also avoids the often tedious installation of GTK+ via MacPorts. However, it misses support for optional Gtk2Hs packages that are currently not supported by the GTK+ OS X Framework, most notably support for Glade. It does include support for Cairo, though.
Here is how to install the library:
- Download and install GTK+ OS X Framework (this uses the standard Mac package installer).
- Install pkg-config, either by compiling it from source or via MacPorts.
- Download and unpack the Gtk2Hs tar ball from the Gtk2Hs download page (I tested 0.10.0).
- Configure with (you may want to remove the two backslashes and put everything on one line)
env PKG_CONFIG_PATH=/Library/Frameworks/Cairo.framework/Resources/dev/lib/pkgconfig:\ /Library/Frameworks/GLib.framework/Resources/dev/lib/pkgconfig:\ /Library/Frameworks/Gtk.framework/Resources/dev/lib/pkgconfig ./configure --disable-gio
- Build with
- Install (to /usr/local/ unless a --prefix option was passed to configure) with
sudo make install
The library is now registered with the package database of the GHC you used for compiling.
NB: Thanks to Ross Mellgren for his post on the gtk2hs-users list that outlined the use of PKG_CONFIG_PATH.